Reuben Saltzman

Deck Guardrail Inspections

The CPSC estimates that between 2003 and 2007, there have been over eleven thousand injuries caused by structural failure or collapse of guardrails at outdoor decks.  It’s not tough to understand why – when people have parties in the summer, everyone hangs out on the deck.  Throw in a keg of Busch Light, a few (ahem) ‘people’ that make the rockin’ world go ’round, and a weak guardrail… boom.  Guardrail collapse.  Weak guardrails are one of the most common safety issues with decks.

The current requirement for new deck guardrails is that they withstand 200 lbs of pressure at any point along the top rail (Table R301.5).  Actually, this standard applies to all guardrails, both inside and outside the house, but decks are the place where it matters most.

My standard method for testing guardrails has always been to just push on them a little.  If they feel weak, I recommend having them reinforced or rebuilt.  Once a guardrail moves an inch or two without much pressure, I stop pushing; I don’t want to be the one to break it.  Home inspections are supposed to be visual, I know, I know… but I like to touch stuff.

I’ve never used any type of testing equipment, but I recently picked up a fancy-schmancy piece of highly specialized deck guardrail testing equipment to help get a better idea of what 200 lbs of pressure felt like.  Jealous much?

Sunbeam Scale

Ok, it’s just an $8 bathroom scale.  After some playing around, I’ve learned that 200 lbs is about the most pressure that I can personally apply to the top rail of a guardrail, just by standing on the ground.  In the photo below I’m applying about 150 lbs of pressure, and I’m straining to do it.

150 pounds of pressure

The weakest point in most guardrails is always going to be at the end, where it terminates next to the house.  All that typically supports the guardrail at this location is the 4×4 post, assuming posts were used to construct the guardrails.   In the photo above, I’m pushing on the guardrail at the end.   This guardrail actually performed fairly well – most guardrails won’t tolerate nearly that much pressure.

The surest way to construct a guardrail that will withstand 200 lbs pounds of pressure is to use metal brackets that are designed just for this purpose.   A couple manufacturers that make such brackets are DeckLok and Simpson Strong-Tie.   If special metal brackets aren’t going to be used, the support posts should be constructed with full size 4x4s (not notched at the bottom), attached with through-bolts, and extra blocking usually needs to be installed to help keep the guardrail secure.

In the photo below, the ovals show where extra blocking was added.  This blocking tremendously stiffens the joist that the guardrail is attached to, making it so the guardrail won’t budge even when a full 200 lbs of pressure is applied.

Nice Guardrail

The bottom line is that weak guardrails are a safety hazard that should be corrected, especially on decks that are high above the ground.  For specific guardrail construction methods and rules, turn to page 15 of the  Prescriptive Residential Wood Deck Construction Guide.

May is Deck Safety Month – Related Post:

How to prevent your deck from collapsing: start by attaching it properly

Reuben Saltzman, Structure Tech Home Inspections – Email – Minnesota Deck Inspector

        

 

7 responses to “Deck Guardrail Inspections”

  1. Penny Antonson
    May 15, 2012, 5:47 am

    Great info thanks, I think our rail needs some help so we will get right on it.

  2. Reuben
    May 15, 2012, 7:50 am

    From a strength standpoint, will it make any difference if the 4×4’s are attached to the inside or outside of the joist?

  3. Jim Allhiser
    May 15, 2012, 7:59 am

    Ha! I am jealous! I don’t think I have ever seen a railing that would stand up to 200lbs. Thanks for the post.

  4. Milind Angolkar
    May 15, 2012, 4:11 pm

    Reuben C: I went with the 4×4 outside mount, through-bolted on mine last year with additional blocking to transfer the torsion force to the other joists. I’d say it’s strong enough that even Senor Saltzman couldn’t take down. I intended to use the Simpson connector but my local box store was out and it was getting late on Sunday that weekend. The main reason I chose the outside mount was the extra floor space on each side.

  5. Reuben Saltzman
    May 16, 2012, 4:37 am

    Reuben – it will generally be stronger if attached inside, but it depends on many different factors. If the post is attached to the outside and special brackets are used, it can be ridiculously strong. You can read through some interesting construction methods here – http://www.structuretech1.com/DeckLokTestData.pdf

    Jim – they seem to be few and far between.

    Milind – the next time I come over, I’m bringing my scale. And a box of tissues.

  6. Milind
    May 20, 2012, 10:20 am

    LOL. You’re gonna need those tissues!

  7. Kevin
    June 13, 2013, 6:26 pm

    Wouldn’t notching the 4×4 post for part/half of it to sit on top of the joist and then thru-bolting it give it that much more strength and rigidity too?

RSS feed for comments on this post.

Comments on posts over 90 days old are disabled, as of 1/7/14.